Holding Tubes Photo Gallery

Contact Us | Order Online

Company
- Capabilities
- Welding
- Machining
- Finishing
- Design
- Engineering
- Associations
- Industry Associations
- Meet Our Staff
- Executive Team
- Sales Team
- Inside Sales
- Alloy Specialists
- International
- Design & Estimating
- Accounting
- Locations
- Springfield, MO
- Raleigh, NC
- Fresno, CA
- Career
  Opportunities
- Positions Available
Products
- Line Card
- All
- Alfa Laval
- Pipetite
- Hydro-Thermal
- Wilden
- Almatec
- Mouvex
- Ace Manufacturing
- Alloys
- AL-6XN Alloy
- Hastelloy C-22
- Pumps
- Centrifugal
- Positive Displacement
- Diaphragm
- Eccentric Disc
- Valves
- Mixproof
- Single Seat
- Specialty
- Control & Indication
- Pipetite
- Standard
- ReBoot
- Sleeve Boot
- Grommet
- Anchors
- Heat Transfer
- Plate Heat Exchangers
- Scraped Surface
- Hydroheaters
- Tank Equipment
- Tank Cleaning
- Weighing Systems
- Other
- Fittings
- Feed-Through Fittings
- Product Recovery
- Tote Unloading Systems
- Tote Tilters
- Filters & Strainers
- Hose
- Dry Disconnect
- Equipment Accessories
Custom Products & Services
- Custom Fabrication
- Transfer Panels
- Utility Stations
- Valve Manifolds
- Tote Unloading System
- Tote Tilters
- High Purity
- Jacketed Tubing
- Holding Tubes
- Special Fittings
- Valve Modifications
- Vessel Trim
- Skid Systems
- Clean In Place
- Food Dairy Beverage
- Pharmaceutical
- Industrial
- Services
- Process Engineering
- Installation
- Pump & Valve Repair
Resources
Photo Galleries

AL-6XN hold tube with square tube frame and adjustable feet. This hold tube is not sloped for economical fabrication.

AL-6XN hold tube with square tube frame, adjustable feet, and lifting lugs. This hold tube is not sloped for economical fabrication.

Sloped stainless steel hold tube with transfer panel for fast and easy hold tube length changes. Transfer panel has provisions for proximity switches.

Non-sloped stainless steel hold tube with square tube frame. Tri-Clamp connection points can be used with a jumper to create different hold tube lengths.

Sloped stainless steel hold tube with transfer panel for fast and easy hold tube length changes. Changing jumper location changes hold tube length.

Non-sloped stainless steel hold tube with square tube frame. Tri-Clamp connection points can be used with a jumper to create different hold tube lengths.

3” and 4” non-sloped stainless steel hold tubes. Upper and lower tube bundles can be run independently or jumpered together for a single long hold tube.

Fully draining sloped stainless steel hold tube with pipe frame and adjustable feet. Hold tube has connections for temperature and pressure sensors.

On this jacketed holding tube, the jackets are sealed to the product tubes with o-rings to prevent jacket seal weld cracking during thermal expansion.

Jacket ends are sealed to product piping with o-rings instead of welding to prevent cracking in high temperature cycle applications.

O-ring sealing jacket ends on this jacketed AL-6XN hold tube make the inner tube section replaceable without having to replace the jacket as well.

This jacketed, insulated stainless steel hold tube has a removable jumper (not shown) for changing between two short or one long hold tube.

Skid Systems

Food, Dairy & Beverage

Pharmaceutical

Industrial

Transfer Panels

Food, Dairy & Beverage

Pharmaceutical

Panel Accessories

Utility Stations
Valve Manifolds
Holding Tubes
Special Fittings
Vessel Trim
Pipetite
Installation

Legal | Site Map | Privacy Policy | Contact Us